![]() ![]() bitmain-cutoff Set bitmain overheat cut off temperature bitmain-auto Adjust bitmain overclock frequency dynamically for best hashrate Send you one of my U3 units to use for testing purposes, right now they canīe had for less than $79 at. Reply to this email directly or view it on GitHubĬgminer 4.8.0 was released and it has native support for the U3, I'mĪssuming if you look at the source code for the antminer library forĬgminer, you may be able to get it to work for bfgminer, if needed, I can Perhaps if more customers ask them forīFGMiner support, that will change. Without the driver, cginer will switch betweenĪll the pools, and the ting that really gets me is I can't connect to theirīitmain has not been supportive of BFGMiner, and we haven't anything to ![]() What I hate, you have to use their cgminer 4.6.1, not 4.7.1 or any other,Īnd NO pool works except for btcguild, why, I don't know, has to be Units, I'll gladly send you mine to see if you can get it to work. Here's the manual, see if it can help, when I get my Butterfly Labs 60GHs Reinstall the driver 8 times today, and if it dies again, I'll have to Works, now it keeps crashing as if the driver goes out, I have had to Use it, doesn't work, after finally finding someone who got it to work, it After about a week,īitmain put the Antminer U3 manual online. Wouldn't work, contacted the seller, he sent me to the discussion onīitcointalk, no one could get the darn thing to work. Please could I ask someone to assist me with figuring out what it wrong with this device? I have looked at the logs but I cannot make sense of the logs as I do not know what I am looking for.Well, I don't have a sample unit, the unit I have is like this. Also, because CGMiner will not start, the device shows no system status information, I cannot see temperature info, I can't see if the hashboards are okay, I can't tell at all where the proble lies. My concern is that the initial run where it got up to 83 degrees has broken the miner, because it doesn't get hot at all currently. Please see these images, they describe what I am seeing:ġ) The device overview where it shows that CGMiner is waiting to start: ģ) The device status I get when I try start CGMiner vis SSH: Ĥ) The event code error as described above: The only visual feedback I have is from the device overview page which gives me the following error: The power supply is fine, and the device itself seems fine and I get get into the web interface as well as connect to the device via SSH. The device does not get hot at all currently.Īt that point I only had 1 pool setup, so I added in 3 just to be sure and tried restarting CGMiner but it still didn't work. I then rebooted the box too but that made no difference. I then restarted CGMiner but it would not restart. I changed the pool settings from factory to the pool information using my chosen pool and worker name for the device. ![]() Within a few minutes the device had cooled down significantly and the fans sped back up to full speed. The device became very hot, 83 degrees I think it was and then the screaming fans seemed to slow down to a crawl. It looked like CGMiner was running and it was mining. When it arrived, I switched it on and it had 3 mining pools already configured from the factory. I have a WhatsMiner M3 that runs CGMiner 4.9.2. While I respect that, I am struggling with support on my kit and I would really appreciate some assistance if possible. I have tried reaching out for assistance in other Bitcoin forums, to no avail as apparently I have bought miner hardware that is not supported by the people who are responsible for CGMiner software. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |